| Nylon |
Pressure Rating:
150 PSIG (10 BAR) Type NEMA 4x, 6 (Submersible) & 12 - IP 68 / IP 69K. Within the Specified clamping range.
Materials:
Fittings: Nylon 6/6
Form Seal: Buna-N
Optional O-Ring: Buna-N, Viton® or Silicone
Optional Seal Ring: Polyethylene or Fiber-Reinforced Plastic
Operating Temperature:
Nylon Fittings: -20ºC to 95ºC (-4ºF to 203ºF)
Available Colors:
Black (RAL 9005)
Gray (RAL 7035)
Blue (RAL 5012) - upon request
Nylon 6/6: V0 rated to UL 94 Flame resistant, halogen and phosphorous free, self-extinguishing, non-toxic, fungus resistant |
| PVDF |
Pressure Rating:
150 PSIG (10 BAR) Type NEMA 4x, 6 (Submersible) & 12 - IP 68 / IP 69K
Materials:
• Nickel Plated Brass
• Form Seal: Viton® (FPM)
• Clamping Insert: PVDF
• O-Ring: Viton® (FPM)
Resistant to:
• Acid
• Salt solution
• Oxydant
• Halogens
• Alcohols
• Chlorinated solvent
• Aliphatic hydrocarbons
• Petrol
|
| Stainless Steel |
Pressure Rating:
150 PSIG (10 BAR) Type NEMA 4x, 6 (Submersible) & 12 - IP 68 / IP 69K. Within the Specified clamping range.
Materials:
Fittings: 316 Stainless Steel
Fittings: 303 Stainless Steel
Form Seal: Buna-N (NBR) or Viton® (FPM)
Clamping Insert: PA (Nylon) or PVDF
O-Ring: Buna-N (FPM), Viton® or Silicone
Operating Temperature:
Buna-N: - 20°C to 95°C (- 4°F to 203°F)
PVDF: - 20°C to 130°C (- 4°F to 266°F) |
|
| Nickel Plated Brass |
Pressure Rating:
150 PSIG (10 BAR) Type NEMA 4x, 6 (Submersible) & 12 - IP 68 / IP 69K. Within the Specified clamping range.
Materials:
Fittings: Nickel Plated Brass
Spring (Flex Extension): Stainless Steel
Form Seal: Buna-N (NBR)
Splined Bushing: Nylon 6/6
O-Ring: Buna-N (Viton® or Silicone optional)
Optional Seal Ring: Polyethylene or Fiber-Reinforced Plastic
Polyamide Operating Temperature:
-60°C to 105°C (-4°F to 203°F)
PVDF / Viton® Operating Temperature:
-20°C to 130°C (-4°F to 266°F)
Nylon 6/6: V0 rated - Flame resistant, halogen and phosphorous free, self extinguishing, non-toxic, fungus resistant |
| Stainless Steel |
(-20°C to 95°C)
(Silicone)-76°F to 356°F
(-60°C to 180°C) |
| FPM |
-13ºF to 392ºF
(-25ºC to 200ºC) |
| Buna-N |
-4 ºF to 212 ºF (-20 ºC to 100 ºC)
Metric: -40 ºF to 212 ºF (-40 ºC to 100 ºC) |
| Adapter, Reducer, Enlarger |
| Nylon/Polypropylene |
-4 ºF to 176 ºF
(-20 ºC to 80 ºC)
|
Nickel Plated Brass
W/O-Ring |
-4 ºF to 176 ºF
(-20 ºC to 80 ºC) |
| 303/316L Stainless Steel w/ Buna-N O-Ring |
(-4º to 203ºF)
(-20ºF to 95ºC
|
| Insert Materials |
Buna-N/TPE
|
- 40 ºF to 212 ºF
(- 20 ºC to 100 ºC) |
| Elastomer |
- 40 ºF to 212 ºF
(- 40 ºC to 100 ºC) |
| FPM |
-13ºF to 392ºF (-25ºC to 200ºC) |
Silicone |
-76ºF to 482ºF (-60ºC to 250ºC) |
| O-Ring & Seal Ring Materials |
Buna-N (NBR)
|
-40°C to 100°C (-40ºF to 212°F) |
| FPM |
-25°C to 200°C (-13°F to 392°F) |
Silicone (VMQ) |
-60°C to 250°C (-76°F to 482°F) |
|
THREAD
SPECIFICATIONS (PITCH & MAJOR DIA.)
|
NPT THREAD
SPECIFICATIONS |
THREAD
SIZE |
1/4" NPT |
3/8" NPT |
1/2" NPT |
3/4" NPT |
1" NPT |
1-1/4" NPT |
1-1/2" NPT |
2" NPT |
Major Dia. Inches (mm) |
.54
(13.72) |
.69
(17.15) |
.84
(21.34) |
1.05
(26.67) |
1.32
(33.40) |
1.66
(42.16) |
1.90
(48.26) |
2.38
(60.33) |
| Pitch (mm) |
.056"
(1.41) |
.056"
(1.41) |
.071"
(1.81) |
.071"
(1.81) |
.087"
(2.21) |
.087"
(2.21) |
.087"
(2.21) |
.087"
(2.21) |
Threads per Inch |
18 |
18 |
14 |
14 |
11.5 |
11.5 |
11.5 |
11.5 |
PG
THREAD SPECIFICATIONS |
THREAD
SIZE |
PG
7* |
PG
9 |
PG
11 |
PG
13.5** |
PG
16 |
PG
21 |
PG
29 |
PG36 |
PG
42 |
PG48 |
Major Dia. Inches (mm) |
.49"
(12.5) |
.60"
(15.2) |
.73"
(18.6) |
.80"
(20.4) |
.89"
(22.5) |
1.11"
(28.3) |
1.46"
(37.0) |
1.85"
(47.0) |
2.13"
(54.0) |
2.39"
(59.3) |
Pitch (mm) |
.05"
(1.27) |
.056"
(1.41) |
.056"
(1.41) |
.056"
(1.41) |
.056"
(1.41) |
.062"
(1.59) |
.062"
(1.59) |
.062"
(1.59) |
.062"
(1.59) |
.062"
(1.59) |
METRIC
THREAD SPECIFICATIONS |
THREAD
SIZE |
M6 |
M8 |
M12 |
M16 |
M20 |
M25 |
M32 |
M40 |
M50 |
M63 |
Major Dia. Inches (mm) |
.24"
(6) |
.31"
(8) |
.47"
(12) |
.63"
(16) |
.79"
(20) |
.98"
(25) |
1.26"
(32) |
1.57"
(40) |
1.97"
(50) |
2.48"
(63) |
Pitch (mm) |
.04"
(1.0) |
.05"
(1.25) |
.06"
(1.5) |
.06"
(1.5) |
.06"
(1.5) |
.06"
(1.5) |
.06"
(1.5) |
.06"
(1.5) |
.06"
(1.5) |
.06"
(1.5) |
BSPP (G)
THREAD SPECIFICATIONS |
THREAD
SIZE |
G 2-1/2" |
G 3" |
G 4" |
Major Dia. Inches (mm) |
2.96 (75.18) |
3.46 (87.88) |
4.45 (113.03) |
Pitch (mm) |
.09 (2.31) |
.09 (2.31) |
.09 (2.31) |
Threads per Inch |
11 |
11 |
11 |
|
.
* PG 7 thread fits 1/4" NPT or 1/2"-20
UNF.
. **
PG 13.5 is also known as PG 13.
. Taps
are readily available. Call for sources and
more detailed PG thread specifications. |
 |
 |
•
World-wide most commonly used type thread
• Characterized by its major diameter and its pitch
• Designated by the letter M followed by the value of the nominal diameter and the pitch, both expressed in millimetres and separated by the multiplication sign '×' (i.e. M12 x 1.5) |
• NPT Thread = National Pipe Thread
• Taper rate for all NPT threads is 1/16
• The taper on NPT threads allows them to form a seal when torqued as the flanks of the threads compress against each other, as opposed to straight thread fittings |
 |
 |
• PG Thread = Panzer-Gewinde
(also Panzer-Rohr-Gewinde)
• German thread type
• Depth of thread smaller than NPT or Metric, but larger flank angle |
• BSPP Thread = British Standard Pipe Parallel Thread
• Parallel (straight) thread with a constant diameter, denoted by the letter G
• Symmetrical V-thread in which the angle between the flanks is 55°
(measured in an axial plane)
• One-sixth of this sharp V is truncated at the top and the bottom
• Threads are rounded equally at crests and roots by circular arcs ending
tangentially with the flanks
• The theoretical depth of the thread is therefore 0.64 times the nominal pitch |
TORQUE
RECOMMENDATIONS FOR STRAIN RELIEF
FITTINGS
Torque in Inch Pounds - in lb (Newton Meters - Nm)
Sizes |
PLASTIC
STRAIN RELIEF FITTINGS |
METAL
STRAIN RELIEF FITTINGS |
|
DOME
NUTS |
THREAD
AND LOCK NUTS |
DOME
NUTS |
THREAD
AND LOCK NUTS |
| M 6
|
|
|
17.7
(2) |
|
| M 8
|
|
|
17.7-26.6
(2-3) |
|
| PG
7, M12x1.5 |
14.4
(1.62) |
22.1
(2.5) |
36.9
(4.17) |
55.3
(6.25) |
| PG
9, PG 11, M16, PG 13.5, 3/8" NPT,
1/2" NPT, M16x1.5, M20x1.5 |
22.1
(2.5) |
33.2
(3.75) |
36.9
(4.17) |
55.3
(6.25) |
| PG 16,
1/2"NPT-E |
29.5
(3.33) |
44.2
(5) |
44.2
(5) |
66.4
(7.5) |
| PG 21,
PG 29, PG 36, PG 42, PG 48, 3/4"NPT,
1"NPT, 1-1/4"NPT, 1-1/2"NPT,
M25x1.5, M32x1.5, M40x1.5, M50x1.5, M63x1.5 |
44.2
(5) |
66.4
(7.5) |
59
(6.67) |
88.5
(10) |
|
| Note: Torque
for dome nuts was determined using a metal rod.
It may vary for cable, depending on the crush
resistance of the cable. We recommend to determine
the actual torque empirically, testing the actual
cable used. The values shown above are for reference
only. |
| Note: Nylon
strain relief fittings installed in a threaded
connection and exposed to elevated temperature
should be retained with a sealant such as Locktite® to
avoid a loose connection when temperature fluctuates. |
Custom Drilling Solutions!
- Any special insert hole or profile configuration is available for a minimum order of 1,000 pieces.
- No Charge Manufacturing Fee - In 12-14 weeks or a one time Expedite Fee reducing manufacturing to 6-8 weeks.
For small quantities we suggest drilling or machining the inserts yourself
Drilling/Machining guidelines:
- We suggest drilling the frozen solid insert.
- Drill holes by using a standard high-speed steel drill bit of the proper size at approx. 2500 RPM.
- Drill holes with insert installed in Strain Relief Fitting as a fixture.
- Keep a minimum distance of 1 mm (.04 in) between holes.
- The outside holes can be located right against the lip of the strain relief body, as sufficient insert material remains between the hole and the body wall
due to the design of the cord grip.
Important:
Design Parameters: Cable diameter should not be less than 80% of hole diameter and the difference between hole and cable diameter should never exceed
.04" (1 mm). The Multi Cable fittings will meet Type NEMA 4x = IP65 if the design parameters are complied with.
To verify a submersible Type NEMA 6= IP68 application, the final assembly of cables and fittings must be tested by the customer or submitted at the customer's
expense to an independent test lab. |
|
We provide cable management solutions