Pressure Rating:
150 PSIG (10 BAR) NEMA 4x, 6 (Submersible) & 12 - IP 68 / IP 69K. Within the Specified clamping range.
Materials:
Fittings: Nylon 6/6
Form Seal: Buna-N
Optional O-Ring: Buna-N, Viton® or Silicone
Optional Seal Ring: Polyethylene or Fiber-Reinforced Plastic
Operating Temperature:
Nylon Fittings: -20ºC to 95ºC (-4ºF to 203ºF)
Available Colors:
Black (RAL 9005)
Gray (RAL 7035)
Blue (RAL 5012) - upon request
Nylon 6/6: V0 rated to UL 94 Flame resistant, halogen and phosphorous free, self-extinguishing, non-toxic, fungus resistant
PVDF
Pressure Rating:
150 PSIG (10 BAR) NEMA 4x, 6 (Submersible) & 12 - IP 68 / IP 69K
(Buna) -4°F to 203°F
(-20°C to 95°C)
(Silicone)-76°F to 356°F (-60°C to 180°C)
Stainless Steel
(Buna) -4°F to 203°F
(-20°C to 95°C)
(Silicone)-76°F to 356°F (-60°C to 180°C)
Insert Materials
Buna-N
-40ºC to 100ºC (-40ºF to 212ºF)
Elastomer
-40ºC to 100ºC (-40ºF to 212ºF)
Viton® (FPM)
-25ºC to 200ºC (-13ºF to 392ºF)
Silicone
-60ºC to 250ºC (-76ºF to 482ºF)
O-Ring & Seal Ring Materials
Buna-N
-30ºC to 120ºC
(-22ºF to 248ºF)
Viton® (FPM)
-40ºC to 200ºC
(-40ºF to 392ºF)
Silicone
-60ºC to 250ºC
(-76ºF to 482ºF)
Polyethylene
-30ºC to 70ºC
(-22ºF to 158ºF)
Fiber-reinforced Plastic
-55ºC to 300ºC
(-67ºF to 572ºF)
Viton® is
a federally registered trademark of DuPont Dow
Elastomer.
THREAD
SPECIFICATIONS (PITCH & MAJOR DIA.)
NPT THREAD
SPECIFICATIONS
THREAD
SIZE
1/4" NPT
3/8" NPT
1/2" NPT
3/4" NPT
1" NPT
1-1/4" NPT
1-1/2" NPT
2" NPT
Major Dia. Inches (mm)
.54
(13.72)
.69
(17.15)
.84
(21.34)
1.05
(26.67)
1.32
(33.40)
1.66
(42.16)
1.90
(48.26)
2.38
(60.33)
Pitch (mm)
.056"
(1.41)
.056"
(1.41)
.071"
(1.81)
.071"
(1.81)
.087"
(2.21)
.087"
(2.21)
.087"
(2.21)
.087"
(2.21)
Threads per Inch
18
18
14
14
11.5
11.5
11.5
11.5
PG
THREAD SPECIFICATIONS
THREAD
SIZE
PG
7*
PG
9
PG
11
PG
13.5**
PG
16
PG
21
PG
29
PG36
PG
42
PG48
Major Dia. Inches (mm)
.49"
(12.5)
.60"
(15.2)
.73"
(18.6)
.80"
(20.4)
.89"
(22.5)
1.11"
(28.3)
1.46"
(37.0)
1.85"
(47.0)
2.13"
(54.0)
2.39"
(59.3)
Pitch (mm)
.05"
(1.27)
.055"
(1.41)
.055"
(1.51)
.056"
(1.41)
.055"
(1.51)
.062"
(1.59)
.062"
(1.59)
.062"
(1.59)
.062"
(1.59)
.062"
(1.59)
METRIC
THREAD SPECIFICATIONS
THREAD
SIZE
M6
M8
M12
M16
M20
M25
M32
M40
M50
M63
Major Dia. Inches (mm)
.24"
(6)
.31"
(8)
.47"
(12)
.63"
(16)
.79"
(20)
.98"
(25)
1.26"
(32)
1.57"
(40)
1.97"
(50)
2.48"
(63)
Pitch (mm)
.04"
(1.0)
.05"
(1.25)
.06"
(1.5)
.06"
(1.5)
.06"
(1.5)
.06"
(1.5)
.06"
(1.5)
.06"
(1.5)
.06"
(1.5)
.06"
(1.5)
.
* PG 7 thread fits 1/4" NPT or 1/2"-20
UNF.
. **
PG 13.5 is also known as PG 13.
. Taps
are readily available. Call for sources and
more detailed PG thread specifications.
•
World-wide most commonly used type thread
• Characterized by its major diameterand its pitch
• Designated by the letter M followed by the value of the nominal diameterand the pitch, both expressed in millimetres and separated by the multiplication sign '×' (i.e. M12 x 1.5)
• NPT Thread = National Pipe Thread
• Taper rate for all NPT threads is 1/16
• The taper on NPT threads allows them to form a seal when torqued as the flanks of the threads compress against each other, as opposed to straight thread fittings
• PG Thread = Panzer-Gewinde
(also Panzer-Rohr-Gewinde)
• German thread type
• Depth of thread smaller than NPT or Metric, but larger flank angle
• BSPP Thread = British Standard Pipe Parallel Thread
• Parallel (straight) thread with a constant diameter, denoted by the letter G
• Symmetrical V-thread in which the angle between the flanks is 55°
(measured in an axial plane)
• One-sixth of this sharp V is truncated at the top and the bottom
• Threads are rounded equally at crests and roots by circular arcs ending
tangentially with the flanks
• The theoretical depth of the thread is therefore 0.64 times the nominal pitch
TORQUE
RECOMMENDATIONS FOR STRAIN RELIEF
FITTINGS Torque in
inlb (Nm)
Note: Torque
for dome nuts was determined using a metal rod.
It may vary for cable, depending on the crush
resistance of the cable. We recommend to determine
the actual torque empirically, testing the actual
cable used. The values shown above are for reference
only.
Note: Nylon
cable glands installed in a threaded
connection and exposed to elevated temperature
should be retained with a sealant such as Locktite® to
avoid a loose connection when temperature fluctuates.
provides
cable products at competitive prices with exemplary customer
service. Inventory in Excess of $25 Million allows the immediate
shipment of almost all standard cable types and sizes.
Cables,
Wires & Accessories: Domestic & Imported Importer
of HELUKABEL®. Approvals: RoHS,
UL, CSA, Harmonized & CE. We offer cables for Power, Control,
High/Low Temp., Hi-Flex, Robotic, Track, Servo, VFD, Composite,
Ribbon, Data(CAT), Single Conductor, etc!
Plastic
Enclosures: Indoor
/ Outdoor NEMA 4x Exclusive importer of HENSEL ENCLOSURES.
Industrial Strength, UV & Impact Resistant, Modular
Expandable. Materials: Polycarbonate, Polystyrene, Powder-coated Steel Types: Gray or Transparent Lids, available with Hinges & Latches, Opaque/ Transparent covers, Plain Walls or Knockouts, Hazardous Location, Fire Proof / Functional Integrity, Offshore Applications Accessories: DIN rails, Mounting plates, Terminal
blocks, Hole plugs, etc.
Pneumatic Components: Fittings, Tubing, Valves & Gauges Fittings: Nickel Plated Brass, Composite, Brass & Compression Fittings, the patented & longstanding Pro-Fit® system, High Pressure Dual Seal fittings, etc. Valves: Flow Control, Manual, Air Piloted, Solenoid, Brass
We also offer Tubing, FRL Units (Filters, Regulators & Lubricators), Gauges, Timers and Relays. Manufacturers include CAMOZZI, COUPLINGS COMPANY, PNEUMADYNE, INFITEC, etc.
Loading
Items For Quote
7374 S. Eagle Street
Centennial, CO 80112-4221 USA
Toll Free: 800-456-9012 / 303-699-1135 Fax: 303-680-5344
Nylon Glands
ATEX IECEx & cUS Glands
Nylon
Cables,
Wires & Accessories: Domestic & Imported
